LABOM MZ1100-B64-W2002 CV3110-A1059-F80-H2100-M1-N10-T30-K1085-W4022-W2674 BH5200 ECO-A99-W5124-W2674 DL8090-HY-D2546-E7-G7-H2-A400-L23-T99-W4035-W1020

İstehsalçı

LABOM

Ölkə

Germany

Çeşid nömrəsi

MZ1100-B64-W2002 CV3110-A1059-F80-H2100-M1-N10-T30-K1085-W4022-W2674 BH5200 ECO-A99-W5124-W2674 DL8090-HY-D2546-E7-G7-H2-A400-L23-T99-W4035-W1020

Təsvir

MZ1100 COMBIBAR PRESSURE MEASURING SYSTEM B64 drawing no.: PD-WV-00178 BOURDON TUBE PRESSURE GAUGE: W2002 CALIBRATION PROTOCOL: with 5 measuring points PRESSURE TRANSMITTER PASCAL CV, for diaphragm seal operation, hygienic acc. to data sheet D4-017/22 CV3110 A1 pressure sensor: piezoresistive for gauge pressure 059 nominal range: 0...16 bar, overload limit 60 bar measuring range setting: turndown 5:1 accuracy: <= 0.15% of measuring span (linearity, hysteresis and repeatability) F80 measuring range: setting see below lower range value: - 1,000 upper range value: + 4,000 unit: bar H21 output signal: 4...20 mA with HART function module 0 setting damping: 0.0 sec. (standard) 0 setting alarm state: < 3.6 mA (standard) M1 display module: without screw cap closed, without window N10 switching module: without case: hygienic housing design with screw cap material: stainless steel degree of protection: IP 66 T30 electrical connection: circular connector M12x1 (4 pin) K1085 design standard process temperature 0...+125 °C, short term up to +140 °C, 1 h ADDITIONAL DESIGN: stainless steel Tag-plate with stainless steel wire marking see below W4022 W2674 EAC-TR certification exemption statement PRESSURE GAUGE DN 100 ECOnomic for food/pharmaceutical/biotechnology acc. to data sheet D2-028-5 BH52 00 case design: IP 65, process connection bottom A99 nominal range: see below -1 ... 4 bar overload protected: 1.3 times pointer: with micro adjusting device for zero-point correction CUSTOMER'S SPECIFICATION: scale: Zeta logo type plate: Labom documentation: Labom W5124 W2674 EAC-TR certification exemption statement DIAPHRAGM SEAL for food/pharmaceutical/biotechnology see data sheet D5-024-3 DL8 090 design: process connection per INGOLD hygienic design per EHEDG Doc.8 and ASME BPE SF3: surface roughness (wetted parts) - turned parts Ra <= 0.76 μm - diaphragm Ra <= 0.38 μm - weld seam Ra <= 0.76 μm HY D25 process connection: DN 25, hexagon union nut A/F 46, G 1 1/4" 46 insertion length: h = 46 mm E7 basic body material: stainless steel mat.-no. 1.4435 (316L), wetted part G7 diaphragm material: stainless steel mat.-no. 1.4435 (316L) H2 gasket: per EPDM -FDA A400 connection of meas. instrument directly welded system filling: Synthetic oil, free of silicon FD1 acc. to FDA 21 CFR 178.3570 / H1-registered L23 DMB_729 T99 temperature, media: see below +10...+150°C W4035 ADDITIONAL DESIGN: wetted parts electropolished W1020 Components marked acc. to material inspection certificate per EN 10204-3.1, wetted parts